Product Catalogue
     
     

     

     
       

     
     
    NEWS LOCATION: HOME  >  NEWS
     
    High Mast Lighting Poles/ Golf Course Lighting
    pubdate:2016-09-09 11:37  click:  Category:NEWS

    Design

    The selection of the correct pole design is predicated on the specifi c loading requirements of each application. The poles located in the steel pole chart are designed to withstand dead loads and theoretical dynamic loads developed by sustained winds of 80 MPH through 110 MPH times the 1.3 gust factor. The combined EPA and the weight of the luminaire, light support brackets, platforms and any other attachments cannot exceed the rated EPA or allowable weight of that pole.

    Welding

    All welds shall be of the highest quality and performed by American Welding Society certifi ed welders conforming to the latest version of the American Welding Society specifi cation AWS D1.1.

    Finish

    All poles, mounting brackets and platforms are furnished with a coating of either red oxide/zinc primer, factory painted, powder coated or hot-dip galvanized to ASTM A-123. Miscellaneous hardware will be galvanized to ASTM A-153. Exterior fi nish coatings are available by request.

    Pole Shaft

    The steel pole shall consist of the appropriate number of pole sections, either round or multi-sided, for heights up to 120 feet. Each section shall be fabricated from high strength low alloy steel conforming to ASTM A-572, with a minimum yield strength of 55,000 psi. These shafts shall telescope over each other to match the overall desired pole height. The overlap telescoping joint shall have a length that is the larger of 2 feet or 1-1/2 times the diameter of the inside of the female tube. The sections shall be pre-fi tted and match marked at the factory. All sections shall maintain a uniform taper from top to bottom. There shall be at least one longitudinal seam weld in the tapered section of the shaft. The longitudinal seam weld shall have at least 60% penetration, except in the areas where the shaft section telescopes over another. In overlapping areas, the weld penetration shall be 100%. No circumferential weld splices may be used in fabricating the shafts. Base Plate

    The base plate is fabricated from a structural quality hot rolled carbon steel plate that meets or exceeds ASTM A-36 with a minimum yield of strength of 42,000 psi. The base plate shall telescope the pole shaft and have a circumferential weld on the top and bottom or shall have a full penetration butt weld with a back up bar. The anchor bolt holes shall be slotted and will be a minimum 1/4” larger than the diameter of the anchor bolts used on the pole.

    Hand Hole

    An oval reinforced hand hole, having a nominal 4” x 6” x .25” wall, will be installed 18” above the base plate. A hand hole cover and attaching hardware is included with each hand hole assembly. A ground lug will be welded inside the pole opposite the hand hole. This is standard on all poles unless otherwise specifi ed. Anchor Bolts Anchor bolts are fabricated from a commercial quality hot-rolled carbon steel bar that meets or exceeds minimum yield strength of 55,000 psi. Anchor bolts

    are sized according to each pole design and are furnished with 2 galvanized heavy hex nuts and 2 galvanized fl at washers. Anchor bolts shall be galvanized a minimum of 6 inches on the threaded end in accordance with ASTM A-153. Anchor bolts will ship with the poles unless otherwise noted.

    Pole Top

    Each pole will be provided with either a removable pole cap, fl at plate, or 2 3/8” O.D. x 5” tenon top (other sizes available).

    The Golf course lighting masts , the usual configuration is that 9 holes have 50-60pcs masts , 18 holes have 110-120pcs masts, each hole has about 5-6pcs masts. Golf Course lighting Telescopic mast system control

     
    Previous:High-Mast LED Solutions a Must for Airport Apron Lighting
    Next:Night Hawk Light Towers/Mobile Light Towers
     
    Company Introduction Learn More
     
    News Learn More
    Nanjing Xuedian Lighting Co.,LtdInc. is the leading manufacture Specialist in production of Pneumatic Telescopic Masts and Mobile Lighting Tower in China.We supply a wide range of Telescopic Masts and Mobile Lighting Towers and solutions for various application such as Fire Departments/Rescue,Police/Security Military Applications,Broadcast and Media,Mobile Transmission ...   Sep 09, 2016  Night Hawk Light Towers/Mobile Light Towers
    Sep 09, 2016  High Mast Lighting Poles/ Golf Course Lighting
    Sep 09, 2016  High-Mast LED Solutions a Must for Airport Apron Lighting
    Sep 09, 2016  High-Mast LED Solutions a Must for Airport Apron Lighting
    Sep 08, 2016  Who uses our portable telescoping antenna mast systems?
    PRODUCTS | ONELINE VIDEO | ABOUT US | NEWS | INQUIRY | CONTACTS | SITEMAP
    Contact:Lee Address: Jiangsu Province, Nanjing Qinhuai District Jiangning Road on the 5th
    Tel:0086-25-85358001 0086-18151686252 QQ:34083670 E-Mail:xdmast@gmail.com Skype:dongsheng.lio1