Operation and technical introduction of lamp lifting bracket which can assemble generator

Time：2020-08-19 View：

The all-round remote control automatic lifting work lamp developed and produced by Nanjing Xuede Technology Co., Ltd. is sold all over the country, and is well received by customers due to its high price-performance ratio. Omni-directional remote control automatic lifting work light is a small movable lighting device integrating generator set, engine, pneumatic lifting light pole and lighting device, which can be used for lighting in fire scene and rescue site. The following is a brief introduction to the specific operating procedures of this mobile lighting equipment with the assistance of experts from the technical department of Xuedian:
1. Place the generator with all-round remote control and automatic lifting work lamp on a relatively flat ground, and press down the lock of the 20,000-direction wheel to lock the wheel to ensure that it does not roll.
2. Loosen the buckle of the cylinder bundled with the telescopic cylinder, pull up the Telescopic cylinder upward with the pin shaft of the cylinder bracket as the fulcrum, and make it stand vertically with the ground, and insert the locking shaft at the bottom of the telescopic cylinder into the shaft hole of the cylinder alignment pins, and tighten the locking screws on the side to make the locking screws tightly support the groove of the cylinder locking shaft.
3. Pull up the lock pin at the lower part of the supporting shaft of the control box, loosen the locking screw, take out the control box outward from the side of the generator set, and then put the supporting shaft of the control box into the top of the telescopic cylinder, make the control box lock pin top in the groove on the top of the cylinder, and tighten the control box lock screw.
4. Insert the aviation plug on the upper side of the telescopic cylinder into the groove at the bottom of the control box, and tighten the input generator output socket of the power output plug-in, then insert the power plug at the bottom of the cylinder and the power plug of the electric air pump into the power output plug of the generator respectively, and insert the air pipe on the air pump into the air nozzle at the bottom of the telescopic cylinder.
5. Wireless remote control enables the whole omni-directional remote control to automatically lift the working lamp to rotate the whole lamp up and down and left and right with the telescopic cylinder as the axis, and can also adjust the illumination angle and orientation of the rotating first lamp head up and down and left and right separately.
6. After adjusting the lamp cap to the required lighting angle and orientation, start the generator according to the operation instructions of the generator; Open the output switch of the generator, the output switch and air pump switch of the power plug of the Air Pump are controlled on the power output plug to inflate the air pump to the Telescopic cylinder. When the Telescopic cylinder grows to the required lighting height, turn off the air pump switch.
7. Turn on the switch of the power plug at the bottom of the control cylinder on the power output plug, and use the remote controller to independently control the opening and closing of each lamp on the control box.
8. After using all-round remote control automatic lifting working light, first turn off the motor according to the operation instructions of the generator, unplug each power plug one by one, press the exhaust valve at the bottom of the telescopic cylinder, make the retractable cylinder drop to its original position section by section.
9. Unscrew the air plug of the telescopic cylinder, loosen the lock screw and lock pin of the control box, and hold the control box vertically upward from the top of the telescopic cylinder, then put the control box back to the control box supporting shaft on the side of the generator set and pin it tightly.
10. Unscrew the locking screws on the side of the cylinder alignment pins, turn the retractable cylinder to the generator side and place it flat on the cylinder bracket, and then buckle the cylinder buckle.

Technical introduction:
In terms of working principle and technical characteristics, this mast is equivalent to a multi-section cylinder. When in use, by injecting and discharging air into the cylinder, the rising and falling movements of each cylinder are realized.
Each cylinder is made of high quality aluminum alloy material. The whole manufacturing process has gone through multiple technological technologies such as extrusion molding, cold drawing, honing, machining, anodic oxidation and so on, and has gone through strict inspection procedures, to ensure the quality of the mast.
If you want to know the structure of the mast, please refer to the structure diagram of the mast. If you want to know more, please refer to the relevant technical instructions or contact Nanjing Xuedian company. You will find the advantages of this mast are: simple structure, but precise manufacturing process, so it is convenient to use and stable in performance, and is your ideal product.
The mast specifications are determined according to the number of nodes, maximum node OD, initial height, and maximum height. Different mast specifications have different technical performance.