Attention and maintenance of mobile lifting lighting car

Time：2020-10-29 View：

Xuedian NJXD all-round mobile lifting lighting car is more suitable for all kinds of large-scale construction work, engineering emergency repair, fire lighting, disaster rescue, accident handling, police case site and other night work sites.

 

III. Precautions:
(1). Please do not use the generator indoors due to the generation of exhaust gas; Do not use it in the direct rain environment. When using, those with flammable substances around should be separated by at least 1 meter; do not smoke when the generator is refueling, and stop the engine before refueling. Do not overflow the gasoline when refueling;
(2). In the working process, please do not disassemble the lamps, otherwise it may cause electric shock. When disassembling, please make sure that all power supply has been cut off;
(3). When the lamps are working, they are very hot. Please make sure that there are no inflammable and inflammable objects around the system, and do not put your hands on the lamps to prevent burns;
(4) when replacing the lamp tube, open the shell of the lamp after it is cooled naturally, and replace the lamp tube with gloves to prevent the fingerprints on the surface of the lamp tube from affecting the service life of the lamp tube;
(5) when the lifting cylinder stretches out or retract, do not put hands or objects at the telescopic point to prevent crushing;
(6). When the lamp works for a long time, it is normal that the lifting cylinder drops slightly, and the lamp pole should be pressurized in time;
(7). Working in the environment such as high-voltage wire, the distance between the high-voltage wire and the high-voltage wire after rising the lamp disc should be at least more than 5 meters, and it should be reliably grounded when used in thundersky and open places, with lightning protection;
(8). If the lamp fails, it should be repaired by professionals or trained personnel. Please do not disassemble it without authorization to prevent injury.

IV. Maintenance:
(1). Clean the surface of lamps before each use;
(2) check the engine oil before each use;
(3). The replacement of engine oil should be used for the first time (or 250 hours), and the engine oil should be changed every 6 months in the future. The replacement process is as follows:
1. Open oil dipstick, loosen the drain screw, and drain the oil. Heat machine drain oil, which can be put faster and more thoroughly.
2. Install the drain screw and tighten it.
3. Add recommended engine oil to the upper limit of engine oil. The oil capacity is about 0.6 liters
4. Install the oil feeler. Please wash your hands with soap and water.
(4). The air filter should be checked every time it is used, and should be cleaned every 3 months or after 50 hours of use, if it is used in a dusty environment, it should be cleaned every one month. The process is as follows;
1. Open the air filter cover and check whether the air filter is clean and in good condition.
2. If the air filter is dirty, remove it and clean it. Replace it if necessary. Wash and squeeze dry with wet soap water or solvent.
3. After cleaning, install the filter element and air filter cover.
Note: Do not turn on the machine after removing the air filter, otherwise dust will pass through the carburetor and enter the engine, speed up the abrasion of the engine.
(5). Oil filter cups are cleaned every 6 months. The process is as follows:
1. Open the fuel valve to the OFF position, open the oil filter Cup counterclockwise, and remove the O-ring and filter screen.
2. Clean the oil Cup, strainer and O-ring with solvent.
3. Replace the rubber pad, and then tighten the oil filter Cup.
4. Check whether the fuel filter is dirty or blocked. If it cannot be cleaned, replace the fuel filter through the outlet.
(6). The spark plug should be cleaned every 6 months and replaced every 1 year. The cleaning process is as follows:
1. Remove the spark plug cap.
2. Remove the spark plug.
3. Clean up carbon deposits.
4. Measure spark plug clearance.
5. Install spark plug and spark plug cap.
(7). Lift mast should be cleaned every 6 months. If it is used in a dusty environment, it should be cleaned every 1 month.

V. Troubleshooting
1. Engine not starting
First, check whether there is fuel in the fuel tank? If not, please add fuel,
Check whether the engine switch is on? If not, turn on the engine switch.
Check whether the engine oil is sufficient? If not enough oil is added.
Check whether the spark plug is good? If not, clean and adjust the spark plug and install it back, and replace the spark plug if necessary.
If it still doesn't start, inform Nanjing Xuedian. It is maintained by professional technicians of Nanjing Xuedian.
2. No voltage output
First, check whether the AC circuit breaker is connected? If not, connect the AC circuit breaker.
Check whether the load appliance is faulty. If there is a fault, replace the equipment or repair it.
If there is still no voltage output, inform Nanjing Xuedian. It is maintained by professional technicians of Nanjing Xuedian.