Application of production process of pneumatic lifting rod in Mobile Command Vehicle

Time：2020-09-18 View：

Introduction to the production process of Xuedian NJXD pneumatic lifting rod
In order to finish the products with good quality and quantity, it is necessary for all the pneumatic lifting rod products of our company to perform according to strict production process. In order to satisfy the market demand and reach high-quality products, the production process of some pneumatic lifting rod products is introduced as follows:
Original data acquisition
I. The production department should select qualified suppliers (including subordinate materials) according to the order and inform the purchasing department to purchase according to the quality request. When the materials enter the factory, it is necessary to go through the strict basis of the quality department ISO9000:2001 quality management system carry out incoming material inspection whether the original data of pneumatic lifting rod (pneumatic mast) purchased by the Institute is qualified or not, and can be put into storage only after it is qualified
Hardware polishing
II. The hardware polishing workshop will polish according to the production order of pneumatic lifting rod and the request of commodity, and enter the semi-product warehouse after passing the inspection (according to the commodity specification)
Injection molding
III. According to the data and performance required by the pneumatic lifting rod products, the injection molding workshop receives materials from the warehouse and passes through the injection molding. In this process, the first thing is the inspection of the mold, the inspection of the first piece and the test installation are qualified before production, (The inspection specification is based on the commodity specification) after being qualified, it will be sent to the pneumatic lifting rod semi-product warehouse.
Plastic polishing
IV. Plastic polishing workshop according to the production order and pneumatic lifting rod commodity request for polishing, after passing the inspection (according to the commodity specification to check) into the pneumatic lifting rod semi-product warehouse
External electroplating
V. According to the production order commodity request to select qualified outsourcing units for processing and electroplating, after returning to the company according to the company's commercial quality specification for inspection (refer to ISO9000:2001 quality management system), after qualified, enter the pneumatic lifting rod semi-product warehouse.
Installation
VI. The assembly and hitchhiking room shall be assembled according to the order of the production department and the product request of the pneumatic lifting rod. The first item shall be inspected and tested before it can be produced in batches, second, the inspection in the production process is based on the quality specification of the supplier (including different customer requests) and then enters the pneumatic lifting rod product warehouse.
Package
VII. The packaging workshop shall carry out the inner and outer packing according to the order of the production department and the commodity request, during which the inspection in the production process shall be conducted according to the quality specification of the supplier (including different customer requests) and then enter the pneumatic lifting rod product warehouse.
Shipment
VIII. Pneumatic lifting rod products shall be sent to customers after passing the inspection.

Application of pneumatic lifting rod in Mobile Command Vehicle
Pneumatic lifting rod products are widely used in public security, fire control, communication, municipal construction and other fields; Can be installed in satellite news interview vehicles, relay vehicles, military, public security command vehicles, emergency communication vehicles and other special vehicles, it is a dual-use product.
The first mobile command vehicle introduced in China made its debut in Shanghai, which attracted the attention of the media. The mobile command vehicle can replace the fixed command post, which can be used for emergency relief command at ordinary times and on-site command during wartime. Its hardware value exceeds 5 million yuan, reaching the international advanced level.
It was revealed that the body of the command car was introduced from the United States, and the car was equipped with various necessary facilities for emergencies such as water and power generation. At present, relevant parties are carrying out software construction such as pre-plan database, basic database, command automation system, GPS positioning system, etc.
It is understood that the vehicle-mounted satellite antenna of the mobile command vehicle can be successfully connected to the satellite within 3 minutes after it is started; A pneumatic lifting rod can carry the earthquake damage images collected on site, after magnifying 20 times, it will be clearly transmitted to the National Earthquake Command Center; Another pneumatic lifting rod will turn on the Searchlight to illuminate the command site; After the command Lan in the mobile command car is turned on, two 42-inch plasma display screens in the car can quickly display the scene...... In the event of an earthquake, the highest decision-making level can enter the mobile command vehicle to enter the state of war office and issue various instructions at any time.
Our current pneumatic lifting rod products are increasingly widely used, and users' requirements for products are also getting higher and higher. Enterprises will have a higher level of product development and research.
Pneumatic lifting rod products are produced by the world's advanced technology, reaching the international first-class level.